445 Small Block Ford Drag Race Engine
Ford Drag Race

445 Small Block Ford Drag Race Engine $25,750

445 Small Block Ford Drag Race Engine Shown With Optional Equipment
445/845HP $25,750
Less Carb & Ignition

You Knew It Was Coming. Scott Couldn't Just Leave Something Good Alone. Our 745HP Ford Really Took Off But A Lot Of People Asked If We Could Build Something Over 800HP Without Taking The Price Into The Stratosphere. Scott Did His Usual Magic And This Is The Result.

Come And Get It While It's Hot!!

  • Horsepower
  • Torque
  • Bore & Stroke
  • Compression Ratio
  • 845 @ 7400 RPM
  • 655 @ 6400 RPM
  • 4.155 x 4.100
  • 15 to 1

  • Dart SHP 9.5" Block w/Splayed 4 Bolt Steel Billet Main Caps
  • Manley 4340 4.100" Forged Steel Crank w/351 SVO Mains
  • Molnar 4340 6.200" Power Adder H-Beam Rods w/ARP 2000 Asymmetrical Bolts
  • Clevite 77 "H" Series Main & Rod Bearings
  • Custom Diamond 15-1 Gas Ported Aluminum Pistons
  • Total Seal .043/.043/3.0MM Ring Set
  • SSRE/Comp Cams Solid Roller Steel Billet Camshaft
  • HIPPO Pro Series Roller Lifters w/Hi-Pressure Pin Oiling
  • Cloyes True Roller Timing Set w/Fuel Pump Eccentric
  • New Design Brodix 15° Head Hunter 302cc Fully CNC Ported Heads
  • 2.180"/1.600" Titanium Valves
  • PAC Racing Roller Springs w/Titanium Retainers & 10° Locks
  • ARP Head Stud Kit w/Parallel Ground Washers
  • T&D "Long Arm" 1.80/1.75 Shaft Rocker System
  • Chromemoly (1) Piece .080" Wall 3/8" Pushrods
  • FelPro HP Head Gaskets w/Pre-Flattened Steel Wire
  • BMP Dominator Aluminum Intake w/Stage II Porting
  • Canton Pro Series Race Pan w/Baffle (1)
  • Melling HP Oil Pump w/Canton Pickup
  • OEM Style Front Cover w/ATI Billet Timing Pointer
  • SFI Approved Harmonic Balancer
  • Sheet Metal Valve Covers
  • Complete Assembly Internally Balanced (2)
  • Individually Dyno Tested & Tuned
  • Actual Dyno Sheet Provided
  • Footnotes:
  • (1) Rear Sump Only.
  • (2) Neutral Balance Flexplate/Flywheel Required.
Shafiroff Racing Engine Options
Fuel System Components
Why Buy A Carburetor From Us?

Yes, you can certainly purchase a stock carb from the big mail order companies but we've seen carbs out of the box down on power as much as 40HP and between 15-20HP is common. That's why we disassemble and blueprint EVERY carburetor before we ever bolt it on your engine. We then tune, adjust and jet your carb on your engine so you get every ounce of power that you paid for.

Even if you're considering one of our Engine Kits or simply looking for a replacement carb, the same blueprint work is done and we dyno test it on a comparable engine to yours before it ships!
 $Priceless
APD 1050 CFM 4500 Series Carb Package includes: 3 Circuit Billet Carb, Phenolic Spacer, Aluminum AN Fuel Fittings, Studs & Gaskets. Dyno Tuned, Jetted and Calibrated on your engine.ImageShafiroff Racing Available Options Close$1395
APD 1150 CFM 4500 Series Carb Package includes: 3 Circuit Billet Carb, Phenolic Spacer, Aluminum AN Fuel Fittings, Studs & Gaskets. Dyno Tuned, Jetted and Calibrated on your engine.ImageShafiroff Racing Available Options Close$1395
APD "Black Widow" 2" SpacerImageShafiroff Racing Available Options Close$175
MagnaFuel ProStar 500 Billet Gerotor Electric Fuel PumpImageShafiroff Racing Available Options Close$430
Igniton Components
MSD Electronic Ignition Package includes MSD Pro Billet Distributor, Steel Distributor Gear, Custom Moroso Wire Set and Loom Kit. Dyno Tested and Calibrated on your engine. $695
MSD 7AL-2 Electronic Ignition Box (Direct Plug-in For Our MSD Distributors) $759
MSD 82613 HVC-2 Coil $265
Crankshafts
Lunati 4340 Forged Steel Crank w/351 SVO Mains $N/C
Pistons - Pins - Rings - Bearings
Total Seal TNT "Hellfire" Rings $175
H13 Tool Steel "Heavy Wall" Wrist Pins $250
Calico Coated Bearing Package $175
Valvetrain
Needle Bearing Tip Option for T&D Shaft Rockers $295
Intake Manifolds
Edelbrock Super Victor Intake Manifold For 4150 Style Carburetors $N/C
Oil Pumps - Oil Pans - Vacuum Pump
Aluminum Rear Sump or Front Sump Pan $325
Additional Parts - Labor - Accessories
Cometic MLS (Multi Layered Steel) Head Gaskets $125
ATI SFI Approved Super Damper Balancer (Includes Hone To Fit Labor) $295
ATI SFI Flexplate - Internally Balanced 157 Tooth 10.5" Bolt Pattern $275
ATI SFI Flexplate - Internally Balanced 164 Tooth 11.5" Bolt Pattern $275
Steel Billet Flywheel - Internally Balanced 157 Tooth 10.5" Bolt Pattern $350
Steel Billet Flywheel - Internally Balanced 164 Tooth 11.5" Bolt Pattern $350
PowerMaster 9603 Hi-Torque Mini Starter. Fits 4.084" block plate with 3/4" depth ring gear. $229