Pump Gas Engines
598/775HP
$16,450
Less Carb & Ignition
With A Little Bit Of Magic And A Custom Proprietary Block, We Can Now Offer You A 598 Low Deck With The Right Rod Length And Piston Design To Give You Incredible Power And Reliability!
|
|
|
|
- Footnotes:
- (1) Precision machined in USA to our custom specifications.
- (2) Composite Fuel Pump Rod Required with our custom camshafts.
- (3) 4150 Style Carb Available.
$495
| Holley Sniper II EFI Package | $2995 | ||||
| Includes: Holley Super Sniper EFI Unit, Sniper EFI Touchscreen LCD Programmer, Bosch LSU 4.9 Wideband Oxygen Sensor, Stainless Steel Clamp-On Oxygen Sensor Installation Kit (May Also Be Welded), Hyperspark Distributor and SSRE Custom Ignition Wires w/Looms. Base Tuneup and Parameters Set and Calibrated on Your Engine. | |||||
| E85 Version | $295 |
If This Fuel Is Readily Available In Your Area, Our E85 Version Offers Much Greater HP And Torque Numbers Over Its' Gasoline Equivalent. E85 Fuel's Ability To Operate Without Detonation Under Much Higher Cylinder Pressure Allows Us To Significantly Raise The Compression Ratio And Slightly Alter Cam Timing To Produce These Dramatic Improvements. You Must Run An E85 Specific Carb Or Program Your Aftermarket Fuel Injection To Work With This Engine.
| "HHR" Hot Hydraulic Roller | $995 |
For Those That Want Even More Power Than "The Classic" Without The Hassle Of Ever Having To Adjust Valves, The HHR Is For You! We Use Special "Proprietary Grinds" On Our Custom Hot Hydraulic Roller Cam Along With "Ultra Hi-Rev" Hydraulic Roller Lifters. This Version Also Comes Standard w/CNC Ported Combustion Chambers And Premium Alloy Valve Springs To Maintain Race Engine Performance With Hydraulic Roller Convenience.
- Brodix 345cc Aluminum Heads w/CNC Ported Chambers
- CNC Ported Combustion Chambers
- Comp Cams Custom "Proprietary Grind" Hydraulic Roller Cam
- High Rev Hydraulic Roller Lifters
- Isky "Enduro Design" Premium Valve Spring Package
- JE/SRP Forged Aluminum Pistons w/Coated Skirts
|
|
| "SS" Saturday Night Special | $1,995 |
The "Saturday Night Special" Package Is Designed For The Hot Rodder That Puts Performance Above All Else. It Combines "Limited" Streetability With "Race Engine" Performance In A Pump Gas Version! This Is The "Bad Boy" Of The Bunch! Putting Out Over 800HP, This Monster Requires Competition Drive Train, Chassis And Exhaust Mods To Deliver Its Maximum Potential. With Its Slightly Higher Compression, More Aggressive Cam And Fully CNC Ported 355cc Dart Pro 1 Aluminum Heads, It Requires A Minimum Of 93 Octane Gas, But That's A Small Price To Pay For The Incredible Performance This Package Delivers.
- Dart Pro 1 Fully CNC Ported 355cc Aluminum Heads
- Manley 1.640" NexTek Roller Springs
- Titanium Retainers w/10° Locks
- Scorpion Race Series 1.7 Aluminum Roller Rockers
- ARP Competition Head Stud Kit
- Comp Cams Custom Ground Steel Billet Solid Roller Cam
- Stage I Merlin X Dominator Intake
- JE/SRP Forged Aluminum Pistons w/Coated Skirts
|
|
| Nitrous Package | $965 | |
Planning On Adding Nitrous? We've Put Together A Preferred Option Package Of Our Most Popular And Highly Recommended Heavy Duty Components ... With The Added Bonus Of Savings!! | ||
| ● Manley 4340 Non-Twist Forged & Nitrided Crank | $250 | |
| ● Manley H-Beam 4340 Steel Rods w/ARP 2000 Bolts | $300 | |
| ● Calico Coated Bearing Package | $175 | |
| ● Total Seal TNT "Hellfire" Rings | $175 | |
| ● Cometic MLS (Multi Layered Steel) Head Gaskets | $125 | |
| ● Dart Inner Valley Stud Kit (Improved Head Gasket Sealing) | $95 | |
| Total Package Value = $1120 - Save $155! | ||
| Fuel System Components | |||||
| Why Buy A Carburetor From Us? Yes, you can certainly purchase a stock carb from the big mail order companies but we've seen carbs out of the box down on power as much as 40HP and between 15-20HP is common. That's why we disassemble and blueprint EVERY carburetor before we ever bolt it on your engine. We then tune, adjust and jet your carb on your engine so you get every ounce of power that you paid for. Even if you're considering one of our Engine Kits or simply looking for a replacement carb, the same blueprint work is done and we dyno test it on a comparable engine to yours before it ships! | $Priceless | ||||
| APD 950 CFM 4150 Series Carb Package includes: 2 Circuit Billet Carb, Phenolic Spacer, Aluminum AN Fuel Fittings, Studs & Gaskets. Dyno Tuned, Jetted and Calibrated on your engine. | Image Close | $995 | |||
| APD 1040 CFM 4150 Series Carb Package includes: 2 Circuit Billet Carb, Phenolic Spacer, Aluminum AN Fuel Fittings, Studs & Gaskets. Dyno Tuned, Jetted and Calibrated on your engine. | Image Close | $995 | |||
| APD 1050 CFM 4500 Series E85 Carb Package includes: 2 Circuit Billet Carb, Phenolic Spacer, Aluminum AN Fuel Fittings, Studs & Gaskets. Dyno Tuned, Jetted and Calibrated on your engine. | Image Close | $1495 | |||
| APD 1050 CFM 4500 Series Carb Package includes: 2 Circuit Billet Carb, Phenolic Spacer, Aluminum AN Fuel Fittings, Studs & Gaskets. Dyno Tuned, Jetted and Calibrated on your engine. | Image Close | $1395 | |||
| Mechanical Fuel Pump Package Includes: High Volume Race Design 6 Valve Pump, Composite Fuel Pump Rod (Required For Our Custom Cams), Braided Fuel Line Inlet Kit w/8AN Lines and Fittings. Plumbed, Installed & Dyno Tested On Your Engine. | $475 | ||||
| Igniton Components | |||||
| MSD Electronic Ignition Package Includes: MSD Pro Billet Distributor, Hi Perf Gear, Custom Moroso 8mm Wire Set. Custom Curved and Calibrated To Your Engine. | $595 | ||||
| MSD 6AL Digital Electronic Ignition Box w/Hi-Speed Rev Limiter | $305 | ||||
| MSD 6AL-2 Digital Electronic Ignition Box w/Launch Control & Hi-Speed Rev Limiter | $480 | ||||
| MSD Blaster 3 Hi Performance Ignition Coil w/HEI Style Post | $65 | ||||
| MSD 8201 Pro Power Coil | $159 | ||||
| Composite Distributor Gear (if required) | Image Close | $125 | |||
| Blocks | |||||
| Dart Inner Valley Stud Kit (Improved Head Gasket Sealing) | $95 | ||||
| Brodix Aluminum Block w/Steel Billet Caps, Special Head Stud Kit & Additional Machining (Slightly Less Peak HP) | $4500 | ||||
| HIP® Process (Hot Isostatic Pressing) For Increased Durability With Aluminum Blocks | $675 | ||||
| Crankshafts | |||||
| Manley 4340 Non-Twist Forged & Nitrided Crank | $250 | ||||
| Callies USA Made 4340 Magnum Plus Pro Series Crank | $2195 | ||||
| Connecting Rods | |||||
| ARP 2000 Rod Bolts | $125 | ||||
| Manley H-Beam 4340 Steel Rods w/ARP 2000 Bolts | $300 | ||||
| Pistons - Pins - Rings - Bearings | |||||
| Total Seal TNT "Hellfire" Rings | $175 | ||||
| Calico Coated Bearing Package | $175 | ||||
| Lifters | |||||
| HIPPO Severe Duty Roller Lifters w/Hi-Pressure Pin Oiling (Extended Lifter Life) | $295 | ||||
| Morel "Black Mamba" Needleless Roller Lifters | $695 | ||||
| Isky Red Zone Solid Roller Lifters w/EZX "Needle Free" Bearing Option | $845 | ||||
| Valvetrain | |||||
| Dart Pro 1 355 Fully CNC Ported Heads (Adds 25HP) | $795 | ||||
| T&D Shaft Rocker System Available In 1.70, 1.75 or 1.80 Ratio (Split Ratio Sets No Extra Charge) | $1795 | ||||
| Crower Stainless Steel Shaft Rocker Arm System. Designed For Severe Duty Street Use. | Image Close | $1995 | |||
| Timing | |||||
| Cloyes 2 Piece Aluminum Timing Cover | Image Close | $195 | |||
| Jesel "Original 2 pc" Belt Drive | $1145 | ||||
| Oil Pumps - Oil Pans - Vacuum Pump | |||||
| Lokar Custom Locking & Calibrated Dipstick (Upgrade) | Image Close | $95 | |||
| Moroso Kickout Style Pro Pan w/Solid Louvered Tray & Main Cap Partitions For Added Power & Oil Control. (Includes New Wing Design Oil Pump) | $395 | ||||
| Vacuum Pump Kit Includes: Moroso 3 Vane Vacuum Pump & Adjustable Relief Valve, AN Fittings, Jones Mandrel & Bracket Kit w/Radius Tooth HTD Belt. | Image Close | $1395 | |||
| Additional Parts - Labor - Accessories | |||||
| Cometic MLS (Multi Layered Steel) Head Gaskets | $125 | ||||
| SFI Approved Harmonic Balancer (Required At All Race Tracks) | $150 | ||||
| ATI SFI Approved Super Damper Balancer (Includes Hone To Fit Labor) | $295 | ||||
| Master Power Silent Drive Vacuum Pump Kit For Power Brakes | Image Close | $625 | |||
| SFI Heavy Duty Flexplate & ARP Bolt Package | $150 | ||||
| Boninfante Severe Duty SFI Flexplate & ARP Bolt Package | Image Close | $229 | |||
| Boninfante SFI Billet Flexplate & ARP Bolt Package | Image Close | $395 | |||
| PowerMaster Hi-Torque Mini Starter | Image Close | $229 | |||
| Painless Performance Hot Shot Relay Kit (Recommended for above starter) | $39 | ||||
| Edelbrock Aluminum "High Volume" Mechanical Water Pump (Short or Long Version) | Image Close | $350 | |||
| Meziere 55GPH Electric Water Pump | Image Close | $575 | |||
| Billet Specialties Tru Trac Serpentine System | Image Close | $Call | |||
| Billet Specialties V-Track Pulley System | Image Close | $Call | |||
| Custom Powder Coating Packages Available | $Call | ||||
| SSRE Powdercoated and Engraved Aluminum Valve Covers | Image Close | $175 | |||
| SSRE Engraved Sheet Metal Valve Covers w/Breathers | Image Close | $375 | |||